U25C preserved is Lake Superior and Ishpeming No. 2501 which is displayed in Marquette, Michigan.

(Joe Ross, CC BY-SA 2.0 <https://creativecommons.org/licenses/by-sa/2.0>, via Wikimedia Commons)

GE U25C DIESEL-ELECTRIC LOCOMOTIVE

The U25C is a diesel locomotive built by General Electric intended for the United States domestic market. Launched in September 1963, it remained in production until December 1965. It was replaced by the U28C.

Penn Central GE U25C 6519 at Cleveland, Ohio, June, 1974. Photographer unknown.

(Craig Garver, Public domain, https://www.flickr.com/photos/digitalrailartist/51049630758/)

Development

The origin of the U25C grew out of the need for six axle locomotives to operate on a 12-mile heavy haul railroad to construct Oroville Dam. The General Electric salesman to Oro Dam Constructors offered essentially a U25B riding on six axle trucks. When the salesman got back to GE's Erie Plant it was discovered that no six axle U25 was available, nor did GE wish to construct a domestic six axle road switcher until the horsepower threshold reached 3000 horsepower. Rather than lose the four unit sale GE quickly began a design of a six axle U25 that relied heavily on the U25B for engineering. The U25C was longer than the U25B by four feet four inches. The extra length was needed to accommodate the improved Trimount trucks. Completed in September 1963 the U25C was the first six axle unit of the second generation of dieselization. Following quickly on the Oro Dam Constructor's order was an order by Atlantic Coast Line for four U25Cs. The ACL also ordered the first four Alco C628s. Both of these ACL orders were delivered in December 1963.

Atlantic Coast Line GE U25C 3004 at Atlanta, Georgia, November 5, 1964. Photographer: unknown.

(Craig Garver, Public domain, https://www.flickr.com/photos/digitalrailartist/50321180696/)

Phases

The following are normally identified as U25C phases:

Phase I

Phase I units were built from September 1963 to May 1964. These units featured a 2900-gallon fuel tank with the air tanks on the ends of the tank. The early U25Cs had louvers on the equipment boxes under the engineer's side of the cab. Oro Dam Constructors Nos. 8010-8016 and Atlantic Coast Line Nos. 3000-3003 were the only examples.

Phase II

Phase II units were built from May 1964 to November 1964. These units had a 3500-gallon fuel tank. The air tanks were relocated to inside the carbody behind the cab. Louvers were placed in the long hood behind the cab for ventilation of the air tanks. There were 24 Phase II units. They were built for Northern Pacific No. 2500-2514, Lake Superior & Ishpeming Nos. 2500-2501, and Atlantic Coast Line Nos. 3004-3010.

Phase III

Built from April 1965 to July 1966. The Phase III units were the most numerous and included the Upgraded U25Cs. A total of 78 U25Cs were built with this carbody. The Phase III U25C carbody overlapped into early Phase I U28C production. A total of 28 Phase I U28Cs used this same carbody. The Phase III had screened panel openings in the carbody behind the cab. Louvers were eliminated from the left side of the carbody, but kept on the engineer's side. A rectangular box opening on the roof provided fresh air for ventilation and cooling the air tanks. Pennsylvania and L&N U25Cs also had an extra equipment box and third handrail stanchion on the raised part of the walkway next to the radiator intake. The extra equipment box was for extended range dynamic brake contactors. In later Phase III production screened doors replaced the screen panels behind the engineer's side of the cab. The louvers behind the engineer's side of the cab were also removed in late production Phase III units.

Lake Superior & Ishpeming GE U25C 2500 at Marquette, Michigan, June 26, 1975. Photographer: Bruce Black.

(Craig Garver, Public domain, https://www.flickr.com/photos/digitalrailartist/51049796361/)

Original Owners

Uprated U25Cs

General Electric built ten uprated U25Cs in 1965. Facing the competitive pressure of the second generation horsepower race GE built these units with increased horsepower. The Alco C628 had more horsepower and the Alco C630 was already announced that Summer. General Motors had the EMD SD40 demonstrators working on several railroads. The increase in unit horsepower was happening that year. The uprated units were built for three railroads that were already operating the U25C. The first uprated units were built for the Northern Pacific between May and July 1965. These were NP Nos. 2518-2520 and were rated at 2750 horsepower. Three more uprated U25Cs were built as Atlantic Coast Line Nos. 3011-3013 in December 1965. The ACL units were rated at 2800 horsepower. The last four uprated U25Cs were rated at 2800 horsepower and were built for the Pennsylvania Railroad in December 1965. These were PRR Nos. 6516-6519. Six additional PRR U25Cs were uprated to 2800 horsepower: 6500-6503, 6510-6511. In early 1966 General Electric began offering the 2800 horsepower U28C. A total of 28 look-a-like U28Cs were built between February 1966 and July 1966 as Chicago Burlington and Quincy Nos. 562-577 and Northern Pacific Nos. 2800-2811.

Preservation

The only U25C preserved is Lake Superior and Ishpeming No. 2501 which is displayed in Marquette, Michigan. (See photo at top of page).

Overview

Type and origin
Power type: Diesel-electric
Builder: GE Transportation Systems
Model: U25C
Build date: September 1963 – December 1965
Total produced: 113
Specifications
Configuration: AAR C-C
Gauge: 4 ft 8+1⁄2 in (1,435 mm)
Length: 64' 6"
Prime mover: GE FDL-16
Generator: GE GT 598
Traction motors: 6X GE752
Cylinders: 16
Performance figures
Power output: 2,500 hp (1,860 kW)
Career
Locale: United States
Disposition: LSI 2501 preserved, remainder scrapped

See Also:

GE Diesels

GE Transportation

Diesel-Electric Locomotives